ADV Pulse

NEWSLETTER
Get ADV Pulse delivered by email
Sign up for ADV Pulse Weekly

Newsletter

Get ADV Pulse delivered by email
Sign up for ADV Pulse Weekly

Connect With Us

Follow On Facebook:

ADV PreppingFive Tips to Help You Deal with a Flat on Tube-Type Tires

Five Tips to Help You Deal with a Flat on Tube-Type Tires

With a little know-how and practice, tire puncture repairs are nothing to fear.

Published on 11.23.2016

None of us ever enjoy getting a flat, but you can often tell how experienced an Adventure Rider is by the way they react to a puncture on tube-type tires. New Adventure Riders tend to throw their fists up in the air and curse the motorcycle gods. Veterans just get down to business because they know that a motorcycle puncture repair is just 15 minutes out of the day if you’re in practice, 25 if you’re a little rusty.

Here are five tips that will help take the pain out of the inevitable flat. We’ll assume that you know how to remove the wheels from your bike and are carrying the proper tools for the job.

1.) You Are Not Stronger Than The Tire

Motorcycle Puncture Repair Tips - putting the bead in the drop center
Position the tire bead in the drop center and you’ll have more room on the opposite side to spoon the tire on.

Motorcycle tires, like car tires, have steel wires embedded in the sidewalls to keep the tire stiff and on the wheel. Think of the wires as hoops, and remember that they will not stretch no matter how hard you try. If you pull one side out, the opposite side will go in.


ADVERTISEMENT

Note also that the circumference of the tire’s bead is smaller than the outer lip of the wheel it has to go over. So how is it even possible to get the tire on the wheel?

The secret is in the center of the wheel. This section of the wheel goes by several names, but we’ll call it the drop center, because it “drops” away toward the hub. The wheel’s circumference is smaller in the drop center. Get the tire bead in the drop center and you can more easily pull the opposite side of the bead over the outer lip of the rim. Moral of the story: If you’re breaking a sweat, you’re doing it wrong.

2.) Your Bike Has a Built-In Bead Breaker

motorcycle puncture repair kickstand bead breaker
Your kickstand can double as a built-in bead breaker if your bike has a center stand.

Some adventure bikes, and quite a few dual sports, have rims with safety beads, which is a raised area near the inner lip of the rim designed to keep the tire in place in the event of a flat. They improve safety, but can make getting the tire bead away from the rim a real chore.

The first technique to try is simply pushing down on the bead with your hands. Often that’s all it takes. If that fails, try stepping on the bead with you boot. Put your full weight on it (make sure the brake disc is up or you could damage it). Jump up and down. Use both feet.

Another method is to use your bike as a bead breaker, provided it has a center stand. First make sure to secure your center stand in place by strapping it to the front wheel so that it doesn’t accidentally roll forward. Next, extend the kickstand, place the tire under it so that the kickstand foots is resting on the edge of the bead, then lean the bike over until the bead pops. Flip the tire over and do the other side.

You can also use your tire irons as bead breakers for stubborn beads. Work them between the tire and the rim, facing up at first, in a small area. As you create a gap, turn the spoons around so they face down and can squeeze between the rim and the tire. Continue working them around and the gap will grow. It’s a lot of work but eventually, the bead will pop off. Motion Pro also makes a set of tire irons with a built-in bead breaker that simplifies the task.

If all else fails, there’s the “nuclear” option: ride the bike, very slowly, for a bit. A flat tire generates a lot of friction and heat. The tire will start to squirm around which will work the bead loose. Note: This is only recommended for rear flats. It’s extremely difficult to control a bike with a flat front tire.

3.) Lubing The Tire: Friend and Foe

motorcycle puncture repair lubing the bead
If you lube the bead of the tire with soapy water, it may make it easier to slide the tire over the rim, but lube also makes it easier for it to slip right back off.

The conventional wisdom is that lubing the tire bead makes it easier to get on and off the wheel. And that is correct; the bead will slide along the outer lip of the wheel much easier with tire lube, soap and water, Windex, etc.

But that also means the bead can just as easily slip back off when you are trying to put the tire back on the rim. You’ll get one section of the bead on, and the side about 90 degrees away will slip right back off. Unless you have a Bead Buddy, or something similar, you’ll feel like you need three hands to get the job done. What if you don’t have a Bead Buddy, or you run out of lube on the trail?

The answer is to practice your technique until you can quickly change a tube with just two tire irons, nothing more. Stand on the edge of the (flat) tire 180 degrees opposite of where you are working the tire irons to make sure the bead is in the drop center of the rim. Get it right and moderate pressure with the irons will move the bead right over the rim, without lube. In fact, the bead is more likely to stay put if it isn’t slippery.

4.) Lever The Tire Off The Disc Side Only

tire puncture repair disc side up
There’s no need to take the tire completely off the rim to repair or replace a tube.

If you’re changing or patching a tube, there’s no need to take the tire completely off the wheel. Break the bead on both sides of the tire, then lever just the disc side off the wheel. Keeping the disc side up while you lever off the tire helps ensure it doesn’t get scratched or bent in the dirt. Once you get the tire off on one side, put your foot on the disc and lift up the tire bead with one hand, then pull out the inner tube with the other.

And don’t forget to run your hand around the inside of the tire and rim once the tube is out. Check for nails, stones or any sharp points that may have caused the flat. Debris can also get into your wheel bearings while you are working on your tire puncture repair, so it’s a good idea to put a rag under the wheel and store your axle and spacers in a clean area.

Keep your axle clean during the repair.
You want to make sure you keep all of your wheel parts clean, organized and out of the dirt. On some bikes, the exhaust pipe can be used as a handy axle holder.

Bonus Tip: It’s possible to patch a tube without taking the wheel off the bike. Some riders break the bead and lever one side of the tire off, then just pull the tube out with the wheel still in place. Of course, this method assumes you are patching the tube, not replacing it.

5) Watch Out For The Dreaded Pinched Tube

motorcycle tire puncture repair
Make sure you push that inner tube down away from the edge of the rim. A little extra precaution can help you avoid re-puncturing a newly repaired inner tube with your tire irons while reinstalling the tire.

The tube is patched or replaced, the tire is back on the wheel, everything looks good. Then you air it up and … it leaks. It’s the dreaded pinch flat and it happens to the best of us.

Somewhere in the process of levering the tire back on, you managed to grab the tube with your tire iron and put a hole in it. Or the tube got twisted inside the tire and damaged when you aired it back up. Either way, it’s coming off and you have to start over again.

One trick for reducing the likelihood of pinch flats with tire irons is to put a couple of pounds of air in the tube before putting it back in the tire. You only want enough to keep the tube free of twists and allow it to roll out of the way of tire levers.

motorcycle puncture repair tips: partially inflate the tube
Put a couple of pounds of air in, then hang the tube on your extended index finger. If it creases about halfway up the tube, you’ve got it right.

Another trick is to remember not to over-rotate your irons. Don’t push the levers past 90 degrees, or perpendicular to the rim. At that point the bead should slide on the rim and you’ll have less of a chance of catching, and damaging, the tube.

Bonus Tip: After reinstalling the tube, use the levers on the bead to guide the valve stem into the hole. With a little air in it, the tube will hold its shape and you can manipulate it by moving the bead, which is much easier than trying to get the valve stem seated with your fingers. A valve stem fishing tool is also handy for getting the valve stem pushed through the hole.

Got some useful tips for fixing flats of your own? Tell us your best tips in the comments!

Photos by Spencer Hill and Bob Whitby

Author: Bob Whitby

Bob has been riding motorcycles since age 19 and working as a journalist since he was 24, which was a long time ago, let’s put it that way. He quit for the better part of a decade to raise a family, then rediscovered adventure, dual sport and enduro riding in the early 2000s. He lives in Arkansas, America’s best-kept secret when it comes to riding destinations, and travels far and wide in search of dirt roads and trails.

Author: Bob Whitby
ADVERTISEMENT

Related Stories

Related Stories

Notify me of new posts via email

Subscribe
Notify of
guest

4 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments
mebgardner
mebgardner
November 23, 2016 4:29 pm

Notice the bearing covers / grease seals are still in place, while the tire is being levered. This is another useful idea for keeping dirt out of the bearing and grease. I pack an old shower curtain for a clean place to work.

OAG
OAG
August 7, 2017 1:05 pm

So, I used the kickstand bead breaker trick, worked like a charm! I have a KLR (no center stand) so I used another KLR as the breaker. Nice tip.

babar69
babar69
September 28, 2019 6:58 am

degrip oil.. .wait 2 min and break the bead every time…. Evaporate super fast, so just a cleaning and you ‘re ok…

Gary Van Den Driesen
Gary Van Den Driesen
November 27, 2020 8:03 pm

Quick puncture fix for tubeless tires only…..carry one or two screws (the wide domed head type) in your kit. If you haven’t done this, you can use any non-essential screw from the bike. Locate the hole in the tire, remove the item that caused the puncture, insert your domed head screw and screw it all the way to the tire. It WILL seal and stay put, but will be even better if you first coat its threads with anything sticky (sealant, superglue etc). Re-inflate tire to normal pressure.

ADVERTISEMENT

Watch: 2024 Triumph Tiger 900 Rally Pro Tested

For 2024, Triumph's dirt-focused Tiger 900 — the Rally Pro — has received...

My First Time Riding Enduro, How Hard Could It Be?

Nestled between the Sierra Nevada and Inyo Mountains of California lies a l...

REV'IT! Tornado 4 Mesh Adventure Jacket

REV’IT! Launches Two New Mesh ADV Suits For Warmer Days Ahead

The thaw is on in North America, and before we know it we’ll be tearing up th...